Seiko MPU-L465 Series User Manual Download Page 21

Page: 21 / 55

- 18 -

(5) REPRINT lamp

The REPRINT lamp lights in case the previous

print can be reprinted.

(6) Interface cover

This cover is used to connect the interface cable

and the AC adapter, and insert the connector.

Open the rubber cover and insert the connector.

(7) Battery rubber cover

This cover is used to mount and secure the

battery pack. Open the rubber cover and then

attach and detach the battery pack.

(8) Battery release lever

This lever is used to remove the battery pack from

the printer.

(9) Paper cover open lever

This lever is used to open the paper cover in order

to install the paper.

(10) Paper outlet port

This is a paper outlet port equipped with a paper

cutter.

(11) Paper guide unit

This unit is used to install paper. Paper with

various width can be installed.

(12) Paper guide

This guide releases the paper guide lock via lever

(13) according to the paper width and changes

the paper guide width. By attaching and

detaching adapters to it, it is possible to fit several

types of inner diameter.

(13) Paper guide lock lever

This lever is used to release the paper guide lock

when changing the position of the left and right

paper guides.

(14) Thermal printhead

This printhead prints characters on the paper. Be

careful that It reaches a high temperature just

after printing.

(15) Paper sensor

This sensor detects “no paper “and “timing-mark.”

(16) Paper cutter

This unit cuts paper.

Summary of Contents for MPU-L465 Series
























































Search results

Summary of Contents for MPU-L465 Series

Reviews:

Related manuals for MPU-L465 Series

Brands by name

Popular brands

Seiko MPU-L465 Series, User Manual

Search results

Summary of Contents for MPU-L465 Series

Reviews:

Related manuals for MPU-L465 Series

Brands by name

Popular brands