Secura Key Radio Key 600e Operating & Installation Manual Download Page 16

Radio Key

®

 600e     

             Operating & Installation

 

Secura Key  

 

12

WARNING

Use of any Auxiliary Reader cable which combines all conductors 

inside one shield and/or uses twisted pair for the antenna lines will 

result in severely reduced reading distance.  Failure to properly ground 

the cable shield for the LED/Beeper lines will also result in severely 

reduced reading distance.

Note:    When power is applied to the RK600e, the unit is calibrated 

for  the  current  antenna  configuration.    Always  connect 

the  Auxiliary  Reader  first,  before  applying  power  to  the 

RK600e. 

Surface-Mounted Wiring

For installations where it is necessary to run cable along the wall surface 

(such as in a wall-mounted modular raceway) small break-away knockouts 

are provided on the bottom of the RK600e and Auxiliary Reader housings, 

as well as on the Spacer.  Remove the knockouts with small pliers, and butt 

the raceway up against the opening in the housing to conceal the cable. 

Power

The RK600e can be powered by the optional RK-PS 12VDC power supply, 

which is rated for powering the RK600e only.  Alternatively, use any good 

9-14 VDC supply which provides at least 150mA.  DC power should be 

clean and filtered with no more than 1 VAC ripple (Peak to Peak).  Do not 

run AC power in the same cable with DC power to the reader. 

RK600e also has protection against accidental polarity reversal or use of 

low voltage AC.  

WARNING

RK600e will not operate on AC Voltage or with DC polarity reversed.

Summary of Contents for Radio Key 600e

























Reviews: