background image

01284 757500

01284 703534

[email protected]

Sole uK distributor, Sealey Group, 

Kempson Way, suffolk Business Park

Bury st. edmunds, suffolk,

iP32 7Ar

www.sealey.co.uk

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

important: 

no liability is accepted for incorrect use of this product. 

WarrantY: 

Guarantee is 12 months from purchase date, proof of which will be required for any claim. 

 

environmental protection

recycle unwanted materials instead of disposing of them as waste. all tools, accessories and packaging should be 

sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.

When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)

into approved containers and dispose of the product and the fluids according to local regulations.

Weee regulations

dispose of this product at the end of its working life in compliance with the eu directive on 

Waste electrical and electronic equipment (Weee). When the product is no longer required, it must be disposed

of in an environmentally protective way. contact your local solid waste authority for recycling information.

 

 

                                                                                       

battery removal

 

 

remove battery from remote.

 

under the Waste batteries and accumulators regulations 2009, Jack Sealey ltd are required to inform potential 

 

purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s  

 

registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.

s

AC9001 | Issue 3 (L) 29/11/16

Original Language Version

© Jack sealey limited

Summary of Contents for Sac9001









Reviews: