background image

7.3.    

cleaning of the handle position and remote control storage area

7.4.    

remove the remote control from the storage area (fig 12). 

7.5.    

clean the handle position and remote control storage area with damp soft cloth only. 

do not

 allow water to drip into the unit. 

do

  

 

not

 soak the cleaning cloth.

8.  movinG the unit

8.5.1.   

to move the unit, hold the top of the air outlet on the front of the unit with one hand and the handle position at the top of the back of  

 

the unit with another hand, (fig 13). ensure that the unit remains upright. 

do not

 hold the horizontal louvre by hand.

8.5.2.   

leave the unit in the upright position when handling or moving it.

8.5.3. 

  

To handle or move the unit, drain the water in the unit first to prevent the water in the unit from flowing onto the ground or carpet.

8.5.4.   

if the remote control is in the position of the handle, take out the remote control, (fig 14).

9.  StoraGe

9.1.    

unscrew the drain cap, unplug the water plug and drain the water in the water tray to a suitable vessel.

 

note:

 

do not

 tilt the unit any further than 30° from vertical.

9.2.    

start the unit, adjust mode to the low fan speed setting, keep the unit in this state for half a day in order to dry the interior of the unit to  

 

prevent mould.

9.3.    

turn off the unit, unplug the power plug, wrap the power cord around the wire-winding post, insert the plug into the storage point on the  

 

rear of the unit; install the water plug and drain cap.

9.4.    

remove the exhaust hose assembly and store appropriately to prevent damage.

 

note:

 to remove the exhaust hose assembly, hold the handle of the exhaust hose retaining clamp, pull the retaining clamp outward

 

evenly, rotate the retaining clamp clockwise to open. remove the exhaust hose assembly.

9.5.    

Pack the air-conditioner in a soft plastic bag. store the unit in a dry and dust proof place. Keep the unit out of the reach of children.

9.6. 

  

remove batteries from the remote control. store remote control in an appropriate place.

9.7.    

ensure that the unit is stored in a dry place.

10.  troubleShootinG

 

Repairs should be carried out by suitably qualified persons only. 

fig.13

fig.14

s

AC9001 | Issue 3 (L) 29/11/16

Original Language Version

© Jack sealey limited

Summary of Contents for Sac9001









Reviews: