Seagull Models SEA 71 Assembly Manual Download Page 11 | Manualshive

Page: 11 / 21

background image

www.seagullmodels.com

11

Repeat the procedure for other aileron.

AILERON PUSHROD INSTALLATION.

Center the servo using the radio system.

M lock

3

Metal Levis.

1) Using a modeling knife, remove the

covering from over the two main gear mount-
ing slots located in the bottom of the wing.

2) Insert the 90º bend of one main gear

wire and support mounting block into the pre-
drilled hole in one mounting slot.

Support
mounting block.

Remove
covering.

Loctite secure.

Aileron pushrods assembly follow pictures

below.

Pushrod L= 114mm.

INSTALLING THE MAIN GEAR WIRES.

3 x 15mm.

Pen.

«
...
9
10
11
12
13
...
»

Summary of Contents for SEA 71






















Reviews:

No comments

Related manuals for SEA 71

Brand: Bachmann Pages: 12

MARINER 40 MK II ARF

Brand: Lanier R/C Pages: 12

MARINER 40 MK II ARF

Brand: Lanier R/C Pages: 3

INTERNATIONAL LIGHTHING

Brand: Sail Classics Pages: 2

THE GHOST HOUSE

Brand: RavensBlight Pages: 10

Blizzard 21 4233

Brand: Multiplex Pages: 40

Brand: H-KING Pages: 4

Brand: Eduard Pages: 8

SPRAY INTELLIGENT DINOSAUR FK501B

Brand: Fei lun Pages: 8

Brand: Eduard Pages: 6

Brand: Hobby King Pages: 15

WORD SCHOOL BILINGUAL ENGLISH/GERMAN

Brand: LEXIBOOK Pages: 4

Brand: Lionel Pages: 8

Brand: Eduard Pages: 7

Brand: Ravensburger Pages: 28

Jaguar A exterior

Brand: Eduard Pages: 4

HMS Exeter 1/350

Brand: Eduard Pages: 6

Rocket Boost Roller Coaster

Brand: KNEX Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands