manualshive.com logo in svg

Seagate STT20000N, Product Manual

Share
Download
Seagate STT20000N Product Manual Download Page 52

Chapter 5

SCSI Interface

Page 44

STT20000A Product Manual

Parameters that control data compression

A Data Compression Enable (DCE) bit of one indicates that  data compression is to
be enabled. When this  bit is set, data sent to the Drive by the Host shall be
processed using the ALDC compression algorithm prior to being written to the
medium. A DCE bit of zero indicates that data compression is disabled.

A Data Compression Capable (DCC) bit of one indicates the Drive support data
compression and shall compress data, using the ALDC algorithm, prior to writing to
the medium when DCE bit is one. A DCC bit of zero indicates the Drive does not
support data compression. This is a non-changeable field.

A Data Decompression Enable (DDE) bit of one indicates that data decompression
is to be enabled. A DDE bit of zero indicates data decompression is disabled.
Normally DDE is always set, on tape drives that support hardware data
compression.

Compression Algorithm defines the data compression algorithm used by the Drive.
The ALDC compression algorithm value is 0001h. This is a non-changeable field.

Decompression Algorithm defines the data decompression algorithm used by the
Drive. The ALDC decompression algorithm value is 0001h. This is a non-
changeable field.

Summary of Contents for STT20000N







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands