manualshive.com logo in svg

Seagate STT20000N, Product Manual

Share
Download
Seagate STT20000N Product Manual Download Page 28

Chapter 3

Installation

Page 20

STT20000A Product Manual

Figure 3-3
Daisy-chain configurations

SCSI Host Adapter

(terminated)

SCSI Tape drive

(not terminated)

other SCSI device

(terminated)

SCSI Host Adapter

(terminated)

other SCSI device

(not terminated)

SCSI Tape drive

(terminated)

1

2

The STT20000 SCSI minicartridge drive supports active termination and does not
require the use of terminating resistor packs.

Terminator power

Terminator power (+5-volt) is enabled by default.

Caution:   If the jumper is installed, be careful not to short the TERMPWR signal to

ground.

The drive contains a terminator power fuse to prevent damage to drive components
in case the terminator power is shorted. If terminator power is enabled and the SCSI
cable is connected upside down for example, this fuse may blow to prevent damage
to the drive itself. In that case, return the drive to an authorized repair facility.

Summary of Contents for STT20000N







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands