manualshive.com logo in svg

Seagate STT20000N, Product Manual

Share
Download
Seagate STT20000N Product Manual Download Page 36

Chapter 4

Drive operation and maintenance

Page 28

STT20000A Product Manual

Using Travan cartridges

The minicartridges recommended for use with the STT20000 SCSI minicartridge
drive are listed in Chapter 2. This section describes some operations using the
cartridges.

Loading and unloading tape cartridges

Your tape drive has a flip-up door that covers the cartridge opening when a tape
cartridge is not installed in the drive. Once a cartridge is inserted, it is held firmly in
place by the drive's positive locking mechanism.

Caution:   DO NOT remove a tape cartridge while the drive is active. Complete

any tape operations and wait until the amber LED is OFF before
removing the cartridge.

To load a cartridge, insert it with the metal base plate down and the tape access
door facing into the drive. Figure 4-2 illustrates the loading of a cartridge.

Figure 4-2
Loading a Travan cartridge

To unload a cartridge, wait until the drive activity LED is OFF and then pull the
cartridge straight out. Figure 4-3 illustrates the unloading of a cartridge.

Figure 4-3
Unloading a Travan cartridge

Summary of Contents for STT20000N







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands