manualshive.com logo in svg

Seagate STT20000N, Product Manual

Share
Download
Seagate STT20000N Product Manual Download Page 4

Important Information About This Manual

All information contained in or disclosed by this document is considered proprietary by Seagate
Technology. By accepting this material, the recipient agrees that this material and the information
contained therein are held in confidence and in trust and will not be used, reproduced in whole or in part,
nor its contents revealed to others, except to meet the purpose for which it was delivered. It is understood
that no right is conveyed to reproduce or translate any item herein disclosed without express written
permission from Seagate Technology.

Seagate Technology provides this manual "as is," without warranty of any kind, either expressed or
implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular
purpose. Seagate Technology reserves the right to change, without notification, the specifications
contained in this manual.

Seagate Technology assumes no responsibility for the accuracy, completeness, sufficiency, or
usefulness of this manual, nor for any problem that might arise from the use of the information in this
manual.

Summary of Contents for STT20000N







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands