manualshive.com logo in svg

Seagate STT20000N, Product Manual

Share
Download
Seagate STT20000N Product Manual Download Page 2

© 1998 Seagate Technology, Inc. All rights reserved

No part of this publication may be reproduced in any form without written permission from Seagate
Technology, Inc.

Publication Number 10005135-001, March 1998

Seagate, Seagate Technology, the Seagate logo and Sidewinder are trademarks or registered
trademarks of Seagate Technology, Inc. Other product names are trademarks or registered trademarks
of their owners.

Seagate reserves the right to change, without notice, product offerings or specifications. Seagate
Technology provides this manual "as is," without warranty of any kind, either expressed or implied,
including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Seagate Technology assumes no responsibility for the accuracy, completeness, sufficiency, or
usefulness of this manual, nor for any problem that might arise from the use of the information in this
manual.

Summary of Contents for STT20000N







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands