background image

E-6

DANGER

 

Never expose the battery to flame or fire, or to excessive heat. 

 

Never attempt to disassemble, alter or directly solder the battery. There are

      no user-serviceable parts. Tampering with battery may expose you to

      dangerous voltage, battery acid, or electrical shock.

 

Never short-circuit the terminals of a battery, as it could result in battery

      leakage, heat generation, fire, or explosion. Avoid contact with all metal

      objects during transporting and storage.

 

When recharging batteries such as nickel metal-hydride or lithium-ion

      batteries, use a charger designed specifically for them and follow the

      recharging instructions. Recharging in an inappropriate charger may cause

      battery leakage, overheating, and explosion.

 

Move leaking batteries away from fire or open flames immediately. 

      The leaked fluid and its vapor are combustible.

 

If the battery leakage contacts your skin or clothing, flush the affected area

      repeatedly with clean water. It may irritate your skin.

      Should it get into your eyes, immediately rinse them with plenty of water,

      avoid rubbing and seek medical advice.

 

Never attempt to insert the battery upside down or backward, as it could

     result in battery leakage or exposion. Always confirm the direction of plus

     and minus before installation.

 

Never connect a battery directly to a plug outlet or car cigarette lighter.

WARNING

 

Keep dry. The battery is not waterproof, and may malfunction if immersed in

      water or exposed to high levels of humidity. Rusting of the internal mechanism

      can cause irreparable damage.

Safety Precautions for Use of Battery

 

SEA&SEA SUNPAK Co., Ltd. assumes no liability for compensation of loss

     of captured images or expenses caused by loss of images, even if you are

     unable to shoot due to a product defect or malfunction.

 

SEA&SEA SUNPAK Co., Ltd. will not be responsible for the replacement or

      compensation for cameras, lenses or those accessories damaged due to

      your invalid operation.

 

Carefully observe the O-ring maintenance manual for the handling of O-rings

     befor use.

 

SEA&SEA SUNPAK Co., Ltd. assumes no liability for errors or discrepancies

     in this manual.

 

Specifications and appearance are subject to change without notice.

Safety Precautions

Summary of Contents for YS-17























Reviews: