Sea-doo 1999 GS Operator'S Manual Download | Manualshive

Page: 79 / 109

background image

77

TRANSPORTATION, STORAGE
AND PRE-SEASON PREPARATION

Transportation

Tie the watercraft to both bow and
stern (front/rear) eyelets so that it is
firmly retained on the trailer. Use addi-
tional tie-downs if necessary.

All Models Except XP Limited

Ensure seat and storage cover are
properly latched.

XP Limited

Ensure engine cover is properly
latched.

All Models

A SEA-DOO cover should protect the
watercraft, particularly before driving
on dirt roads, to prevent dirt entry
through the air intake opening(s).

Observe trailering safety precautions.

Storage

It is recommended that the watercraft
be serviced by an authorized Sea-Doo
dealer for storage but the following
operations can be performed by you
with a minimum of tools.

Engine Draining

All Models Except GSX RFI and
GTX RFI

Check engine drain hose (lowest hose
of engine). Make sure there is no sand
or other particles in it and that it is not
obstructed so that water can leave the
engine. Clean hose and fitting as nec-
essary.

◆

WARNING

Always turn the fuel valve to OFF
position when transporting or
docking the watercraft.

-

CAUTION

Do not route ropes or tie-downs
over the seat as they could pro-
duce permanent damage. Wrap
ropes or tie-downs with rags or
similar protectors where they can
touch the watercraft body.

-

CAUTION

Do not run the engine during the
storage period.

-

CAUTION

Water in engine drain hose must
be free to flow out, otherwise wa-
ter could be trapped in engine.
Should water freeze in engine,
severe damage will occur. Check
engine drain hose for obstruc-
tions.

Smo9901b.fm Page 77 Friday, September 4, 1998 10:45 AM

www.SeaDooManuals.net

«
...
77
78
79
80
81
...
»

Summary of Contents for 1999 GS














































































































Reviews:

No comments

Related manuals for 1999 GS

Mackinaw 156 Canoe

Brand: KL Industries Pages: 5

Brand: Ocean Yachts Pages: 50

Brand: Feathercraft Pages: 8

Brand: Yamaha Pages: 58

Mirage Inflatables

Brand: Hobie Pages: 2

Brand: Axopar Pages: 134

Brand: Coastal Pages: 16

Brand: 3D Tender Pages: 18

Brand: Polaris Pages: 241

Brand: Paddle King Pages: 11

WaveRunner GP800R

Brand: Yamaha Pages: 247

Nautica 450 RACE

Brand: Nautica Boats Pages: 20

Brand: Hunter Marine Pages: 49

Brand: Hunter Marine Pages: 181

WaveRunner XL800 2001

Brand: Yamaha Pages: 136

WaveRunner VX110 Sport

Brand: Yamaha Pages: 26

AIRIS 16425 PLAY 8

Brand: Walker Bay Pages: 22

Brand: Speed Sails Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands