Sea-doo 1999 GS Operator'S Manual Download

Page: 77 / 109

Locate MPEM on the left side of wa-
tercraft.

Remove fuse cover from the MPEM.

TYPICAL

1. MPEM
2. Fuse cover

Use the tabs of the fuse cover to re-
move and reinstall fuses.

1. Fuse cover
2. Fuse tabs

To access fuse in the electrical box,
proceed as follows:

Open the engine cover and remove
storage basket (XP Limited).

Remove seat (except XP Limited).

Remove vent tube support (GS and
GSX Limited).

Locate the electrical box.

Unclip and remove cover of the elec-
trical box.

GS AND GTI MODELS

1. Fuse holder

GSX LIMITED, GTX LIMITED AND
XP LIMITED

1. Fuse holder

All Models

If defective, replace the fuse by one of
the same rating.

F06H1SY

F06H1TY

CAUTION

Do not use a higher rated fuse as
this can cause severe damage.
Refer to SPECIFICATIONS section
for recommended fuse rating. If a
fuse is regularly burnt, refer to an
authorized dealer.

◆

WARNING

If any water is found in the elec-
trical box(es), immediately refer
to an authorized Sea-Doo dealer
before operating the watercraft.

F06H1UY

F07H0IY

Smo9901b.fm Page 75 Thursday, October 1, 1998 1:42 PM

www.SeaDooManuals.net

Summary of Contents for 1999 GS














































































































Search results

Summary of Contents for 1999 GS

Reviews:

Related manuals for 1999 GS

Brands by name

Popular brands

Sea-doo 1999 GS, Operator'S Manual

Search results

Summary of Contents for 1999 GS

Reviews:

Related manuals for 1999 GS

Brands by name

Popular brands