Hobie Brave Assembly Manual Download

Page: 1 / 16

ASSEMBLY MANUAL

TABLE OF CONTENT

Hobie Bravo terminology ............................................................................................. 2

List of the parts ............................................................................................................ 3

Frame and mast ball .................................................................................................... 4

Righting line ................................................................................................................. 5

Sail............................................................................................................................... 6

Mast assembly............................................................................................................. 7

Mast and sail assembly ............................................................................................... 8

Mast float ................................................................................................................... 10

Rudder ....................................................................................................................... 11

Stepping the mast...................................................................................................... 12

Mainsheet system...................................................................................................... 13

Unfurling/furling the sail ............................................................................................. 14

Boom (option) ............................................................................................................ 15

Reefing the sail .......................................................................................................... 16

Summary of Contents for Brave

















Search results

Summary of Contents for Brave

Reviews:

Related manuals for Brave

Brands by name

Popular brands

Hobie Brave, Assembly Manual

Search results

Summary of Contents for Brave

Reviews:

Related manuals for Brave

Brands by name

Popular brands