background image

E-6

Safety Precautions for Use of Battery

Safety Precautions

Carefully observe the O-ring maintenance manual for the handling of O-rings 

befor use.

SEA&SEA SUNPAK Co., Ltd. assumes no liability for errors or discrepancies 

in this manual.

Specifications and appearance are subject to change without notice.

The silicon grease included in the product package is inedible.

DANGER

Never expose the battery to flame or fire, or to excessive heat. 

Never attempt to disassemble, alter or directly solder the battery. There are no 

user-serviceable parts. Tampering with battery may expose you to dangerous 

voltage, battery acid, or electrical shock.

Never short-circuit the terminals of a battery, as it could result in battery 

leakage, heat generation, fire, or explosion. Avoid contact with all metal 

objects during transporting and storage.

When recharging batteries such as nickel metal-hydride or lithium-ion 

batteries, use a charger designed specifically for them and follow the recharging 

instructions. Recharging in an inappropriate charger may cause battery leakage, 

overheating, and explosion.

Move leaking batteries away from fire or open flames immediately.  The leaked 

fluid and its vapor are combustible.

If the battery leakage contacts your skin or clothing, flush the affected area 

repeatedly with clean water. It may irritate your skin.

Should it get into your eyes, immediately rinse them with plenty of water, avoid 

rubbing and seek medical advice.

Never attempt to insert the battery upside down or backward, as it could result 

in battery leakage or exposion. Always confirm the direction of plus and minus 

before installation.

Never connect a battery directly to a plug outlet or car cigarette lighter.

WARNING

Keep dry. The battery is not waterproof, and may malfunction if immersed in 

water or exposed to high levels of humidity. Rusting of the internal mechanism 

can cause irreparable damage.

Do not remove and/or damage the case of a battery. It may cause battery 

leakage, overheating or explosion.

Do not charge a rechargeable battery beyond the specified charging time, it 

may cause battery leakage, fire hazard or explosion.

Summary of Contents for YS-01



























Reviews: