Sea & Sea YS-01 Instruction Manual Download Page 4

E-3

For safe handling of the product, please read the following precautions 

carefully before use. 

Situations that involve a high risk of severe injury or

death. 

DANGER

Situations that could result in severe injury or death.

WARNING

Situations that could result in property damage or

personal injury.  

CAUTION

Failure to heed the precautions listed below could result in serious 

consequences. To prevent injury or damage to yourself and/or

others, please observe the precautions as they contain highly

important information related to personal and product safety.

DANGER

WARNING

Safety Precautions 

Never attempt to disassemble, repair or alter the product yourself to prevent 

significant electrical hazard due to the high-voltage circuitry in the product. 

Do not heat the product or put it into a fire, this could result in explosion or fire. 

Unauthorized disassembling and/or modification could result in malfunction or 

flooding, and avoid product warranty. Take the product to a SEA&SEA authorized 

service center for repair or inspection.

Use only batteries approved for use in this product. Do not mix old and new 

batteries of different types.

Remove batteries before transport or storage, or when you are not going to use 

the product for an extended period of time, to prevent unexpected activation.

Pay particular attention to opening the battery cap to avoid injury. Heat from 

the batteries may cause pressure buildup inside the battery compartment, 

and could result in cap explosion with unexpected force.

Avoid water or foreign objects inside the product. Discontinue use and turn it 

off immediately should you notice flooding or leakage. Continuous use could 

result in complete damage to the product.

Do not handle batteries wet hands to prevent shock hazards.

Do not use the product in the presence of flammable gas, as this could result 

in explosion or fire.

Do not fire the strobe/light with the reflector touching a person or object to 

prevent heat generation. Touching the reflector immediately after firing could 

result in burns. 

Summary of Contents for YS-01



























Reviews: