manualshive.com logo in svg

SE3D r3bEL mini, User Manual, Page: 48 / 51

Share
Download
SE3D r3bEL mini User Manual Download Page 48

 

r3bEL mini User Manual 

 

48 

 

 

11

 

Troubleshooting guide 

Issue 

Solution 

No power  

Is the small green light on the power supply turned on? 

NO 

1.

 

Contact SE3D technical support for replacement power 
supply. 

 

YES  

1.

 

Check wires connecting the V+ and V- terminals on the 
power supply to the controller board. Secure any loose 
connections. 

2.

 

Contact SE3D technical support. 
 

No connection to 
computer 

To check if your computer is connected to the controller board, 
check the red light behind the Micro USB connector is lit up. The 
Pronterface application should also display the following: 
 

 

 
Almost all connection problems can be solved by following these 
steps in order: 

1.

 

Turn off printer 

2.

 

Unplug USB cable from computer 

3.

 

Close Pronterface application 

4.

 

Plug USB cable into printer and computer 

5.

 

Open Pronterface application 

6.

 

Connect to printer 

 
If the problem is still not solved, check the following  settings in 
Pronterface: 

1.

 

The correct port is selected 

2.

 

The Baudrate is set to 115200 (250000 should also work) 

 
 
 
 
 

Summary of Contents for r3bEL mini




















































Reviews:

No comments