background image

 
VERSO 50_v1.0.27_EN                                        33502027401_3_1                                                  page 17/24 

2- 6  M5 - Alarms list 

You will see a general screen for the setup of the alarms, composed by 4 pages. In the first page, select and confirm the parameter 
“a” to choose the code of the alarm. In the upper part of the screen you will see the name of the correspondant alarm. Then modify 
the parameters from “d” to “l” as you prefer. Return then to the first page and confirm the parameter “c” to save the modifications. 
 
 
 
 
 
 
 
 
 
 
 
For every alarm, you can program all the following parameters: 
 

POS. 

NAME 

DESCRIPTION 

RANGE 

Alarm code 

Select this parameter to choose the alarm that you want to set. All the parameters in the 
next pages refer to the alarm selected in this parameter. In the upper part of the screen 
you will see also the name corresponding to the code that you are selecting. 

Category of 

the alarm 

Not selectable parameter. 

Save alarm 

Parameter that has to be confirmed with the “i” button to save all the parameters from D to 
L in the configuration of the alarm selected at parameter A. 

Activation 

It permits to choose when the alarm condition must be verified and make the alarm 
appear: Always (always enabled), Run (active only with engine running) or Disabled 
(disabled). 

Always 

Run 

Disabled 

Delay 

Before the activation of the alarm, the cause must remain present for this time. 

0-255 [s] 

Retentive 

Choose if the alarm must be retentive (ON: the alarm indication remains on display until 
you press the reset button, even if the cause has disappeared) or not (OFF: the alarm 
indications disappears when the cause disappears). 

ON 

OFF 

Action 

Select the action in consequence of the activation of the alarm: Warning (only indication), 
Stop (the alarm stops the engine immediately) or Cooling (the alarms stops the engine 
with cooling). 

Warning 

Stop 

Cooling 

Siren 

Function not available. 

ON 

OFF 

SMS 

Function not available. 

ON 

OFF 

Global 1 

If On, the alarm activates the output set as Global alarm 1 (if present).

 

ON 

OFF 

Global KG 

If On, if the alarm is active KG cannot be closed.

 

ON 

OFF 

Global KR 

If On, if the alarm is active KR cannot be closed. 

ON 

OFF 

Summary of Contents for VERSO 50

























Reviews: