manualshive.com logo in svg

SCS CTE701, Operating Instructions Manual, Page: 9 / 11

Share
Download
SCS CTE701 Operating Instructions Manual Download Page 9

TB-9031

 Page 9 of 11

© 2022 DESCO INDUSTRIES INC

Employee Owned

SCS 

- 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: 

StaticControl.com

8.  Disconnect the red test lead from the monitor's tool 

cord. 

9.  Reinstall the tool cord to the metal tool.

Ground Man Plus Workstation Monitor

CONFIGURING THE VERIFICATION TESTER

Configure the Verification Tester's DIP switch to the 

settings shown below. This will make its test limits 

match the factory default limits of the monitor.

VERIFYING THE OPERATOR CIRCUIT

1.  Use the black test lead to connect the Verification 

Tester to equipment ground. 

2.  Power the Verification Tester ON. 
3.  Use the 3.5 mm mono cable to connect the 

Verification Tester to the monitor's operator jack. 

The monitor's operator LED will illuminate red, and 

its alarm will sound. 

Figure 28. Pressing the WRIST STRAP and HIGH BODY 

VOLTAGE test switches simultaneously

Figure 25. Connecting the Verification Tester to the 

Ground Man Plus Workstation Monitor's operator jack

Figure 26. Pressing the WRIST STRAP test switch

Figure 27. Pressing the WRIST STRAP and LOW BODY 

VOLTAGE test switches simultaneously

4.  Press and hold the Verification Tester's WRIST 

STRAP test switch. The monitor's operator LED will 

illuminate green, and its audible alarm will stop. This 

verifies the operator circuit's impedance limit. 

5.  Continue to press and hold the Verification Tester's 

WRIST STRAP test switch. Simultaneously, press 

and hold the Verification Tester's LOW BODY 

VOLTAGE test switch. The monitor's operator LED 

will remain green, and no audible alarm will sound. 

This verifies the operator circuit's low body voltage 

limit. 

6.  Continue to press and hold the Verification Tester's 

WRIST STRAP test switch. Simultaneously, press 

and hold the Verification Tester's HIGH BODY 

VOLTAGE test switch. The monitor's green operator 

LED will illuminate continuously, its red LED will 

blink, and an audible alarm will sound. This verifies 

the operator circuit's high body voltage limit. 

7.  Disconnect the mono cable from the monitor.

Summary of Contents for CTE701












Reviews:

No comments