manualshive.com logo in svg

SCS CTE701, Operating Instructions Manual, Page: 11 / 11

Share
Download
SCS CTE701 Operating Instructions Manual Download Page 11

TB-9031

 Page 11 of 11

© 2022 DESCO INDUSTRIES INC

Employee Owned

SCS 

- 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: 

StaticControl.com

Limited Warranty, Warranty Exclusions, Limit 

of Liability and RMA Request Instructions

See the SCS Warranty - 

StaticControl.com/Limited-Warranty.aspx

Maintenance

Battery Replacement

Replace the battery once the Low Battery LED 

illuminates red. Open the compartment located on the 

back of the tester to replace the battery. The tester 

uses one 9V alkaline battery. Ensure that the battery's 

polarities are oriented correctly to avoid possible circuit 

damage.

Specifications

Operating Temperature 50 to 95°F (10 to 35°C)
Environmental 

Requirements

Indoor use only at altitudes 

less than 6500 ft. (2 km)
Maximum relative humidity 

of 80% up to 85°F (30°C) 

decreasing linearly to 50% @ 

85°F (30°C)

Dimensions

4.9" L x 2.8" W x 1.3" H

(124 mm x 71 mm x 33 mm)

Weight

0.2 lbs. (0.1 kg)

Country of Origin

United States of America

Summary of Contents for CTE701












Reviews:

No comments