background image

OPERATING INSTRUCTIONS

 

19

CG700 rondo

Version: 27202 - 

D

Schmalenberger GmbH + Co. KG 

D-72072 Tübingen / Germany

Please observe:

The mains power connection must be a fixed connection.

Under no circumstances must there be any conducting connection between the metal
parts of the motor and the water.

The mains power supply cable must be equipped with an all-pole separator with a
contact opening of 3 mm.

At the marked connection terminal (at the foot of the motor or next to the terminal box)
an equalising potential with a cross-section of  10 mm² must be fitted.

5.2

Electrical connections AC 

Protective measures:

fig. 29   

Mains voltage: 

230 V for 1 ~ AC

Mains power supply cable:

3 x 2.5 mm²

Pump connection cable:

 3 x 2.5 mm²

Fuse:

16 A passive

=

Control unit in the pool

Motor of the circulation pump

Mains power supply 
(230 V for 1~)

= Switchgear 

cabinet

B

 

= Capacitor

Connection cable, for example,
HO7RNF, all further details required for
making connections can be found in
chapter 3.1.

fig. 30: Basic circuit diagram for 230 V 

for 1 ~ AC

An earth leakage circuit breaker
(nominal fault current 

30 mA) must be

fitted to the mains power supply!

Important! Watch the order of the
terminal bridges!

See the inside of the terminal box lid or
enclosed circuit diagram. Please be sure
to observe instructions from the motor
manufacturer!

L

External conductor

N

Neutral conductor

8236

8464

Summary of Contents for fluvo CG700 rondo

































Reviews: