background image

OPERATING INSTRUCTIONS

 

15

CG700 rondo

Version: 27202 - 

D

Schmalenberger GmbH + Co. KG 

D-72072 Tübingen / Germany

4.11

Connection to the pump

4.12

Installing the switchgear cabinet

fig. 21

01

Motor

12

Air pipe clamp

13

Hose line pressure side

16

Hose line suction side

Connect the hose lines (13 pressure side
+ 16 suction side) to the pump body. Use
the corresponding air pipe clamps (12)
on both sides for this. 

Warning!

Make sure that the connections

 

 from the

body of the pump to the installation kit /
pipework are as nearly aligned as is
possible. 
The hose lines must always be attached
to the pump on the one side
(compensator function), see diagram.

fig. 22

K

 Protective hose

02

Switchgear cabinet

31

Switching tube

Mount the switchgear cabinet (02) as
close as possible to the installation kit.
Also please observe the instructions in
chapter 4.2. 
Fix the switching tube (31) onto the
nipple in the protective hose (K).

Warning!

Be careful not to put a kink in the
switching tube and keep it as short as
possible, maximum length 8 m.

8228

8229

Summary of Contents for fluvo CG700 rondo

































Reviews: