Schlegel PXFE868, Mounting And Wiring Instructions

Page: 4 / 12

Georg Schlegel GmbH & Co. KG Kapellenweg 4 · 88525 Dür
mentingen · www
.schlegel.biz I V01
PXFE868
4 / 12
®
Montage- und Anschlussanleitung / Funkempfänger
Mounting and wiring instructions / Wireless receiver
Instructions de montage et de câblage / Récepteur sans fil
English
Operation mode LED 1 LED MD Function
Relay energised on flashes Relay energised by provid-
Relay energised,
inverse output
on on Relay energised by pro-
viding operating voltage,
inverse output signal
Switch functions
Linkage flashes
slowly
on Relay energised as soon as
one switch is actuated, de-
energises when all taught-in
switches are not actuated
Latching function on flashes Latching function/impulse
Wiping
function
flashes
slowly
flashes
slowly
Wiping function, contact au-
tomatically de-energises after
the set time
Additional func-
Battery moni-
toring
off (LED
3 flash-
es)
flashes
slowly
Relay K3 indicates under-
voltage of the taught-in and
battery-powered switches/
transmitters
Status monitor-
ing
off (LED
4 flash-
es)
flashes
slowly
Relay K4 indicates status
error; activates function only
in combination »switch with
status signal«
Notice
If only one or both additional functions are activated, no further wireless
transmitter can be taught in.
Operation mode wiping contact
- Choose or select wiping function. LED MD flashes.
- With each flashing of the LED, the wiping time is increased by 1 s.
- Count the impulses of the flashing LED and confirm the desired time by
pressing the LRN push-button.
- In order to change the wiping contact time, start selection of operation
mode and select wiping function again.
Operation mode status monitoring
- After selection of status monitoring the LED MD flashes
every second.
- The LEDs 1-4 indicate the adjustable status times.
- The display of the LED changes every 5 s (see table).
- If the required LED combination is indicated, press the LRN push- but-
ton for 1 s. The desired operation mode is now activated.
- Without confirmation of the selection, the standard value of 10 s
is set.
Status
signal time
LED 1 LED 2 LED 3 LED 4 LED MD
10 s on off off off flashes every s
100 s on on off off flashes every s
1000 s on on on off flashes every s
10000 s on on on on flashes every s
Function: If no status information is given by the taught-in switches, relay
K4 automatically gives the alarm after 2.2 times the status time.
Attention! Please ensure that the taught-in wireless transmitter is set to
the correct status signal.
Teaching in of switch
- Press push-button LRN approx. 1 s -> LED MD flashes slowly (2 Hz).
- Press push-button SEL for channel seletion.
- Actuate switch/command device to be taught in -> the LED of the cor-
responding channel is off for short time.
- To leave teach-in mode press push-button LRN for approx. 1 s -> LED
MD is on.
Deleting one switch
- Press push-button LRN for 5 s until LED MD flashes fast (5 Hz).
- Press push-button SEL for channel seletion.
- Actuate switch/command device to be deleted -> the LED of the corre-
sponding channel flashes for a short time.
- Press push-button LRN for approx. 1 s to leave delete mode.
Inverse teaching in of one switch
- Procedure like teach-in but switch must be actuated before proce-
dure is started by pressing LRN.
Deleting all switches
- Press push-button LRN for 5 s until LED MD flashes fast (5 Hz).
- LED 1 is on -> release push-button LRN.
- Press push-button LRN for 5 s again.
- LED MD is on and LED 1 flashes fast -> release push-button LRN.
- Operation mode was set back to standard.