Saturn KDB - 161 GOM Manual Download Page 90

Page: 90 / 106

KDB-GOM

Series

- 90 -

Part name

High limit sensor

Replacement steps

Disassemb

①

Unplug the boiler form the electric outlet.

②

Open the front cover.

③

Separate the overheating prevention device’s two terminals (red).

④

Remove the clip fixing the overheating prevention device ( or unscrew the two screws ).

⑤

Separate the overheating prevention device.

sse

①

Fix the overheating prevention device by inserting the clip (or screw the two screws ).

②

Connect the overheating prevention device wire.

③

Close the front cover.

④

Plug the boiler into the electric outlet.

Caution

1. Make sure fixation is done correctly.
2. Make sure the connecting jack is assembled correctly.

⑤

④

Summary of Contents for KDB - 161 GOM











































































































Search results

Summary of Contents for KDB - 161 GOM

Reviews:

Related manuals for KDB - 161 GOM

Brands by name

Popular brands

Saturn KDB - 161 GOM, Manual

Search results

Summary of Contents for KDB - 161 GOM

Reviews:

Related manuals for KDB - 161 GOM

Brands by name

Popular brands