background image

CONN

E

CT

IO

N

 

Dataloggers SenNet DL150 / DL151 / DL170 / DL171 / DL172. Technical manual

 

42

 

Satel Spain 

 

Version 1.01

 

8.

 

CONNECTION OF THE DL172 

 

8.1.

 

Connection to the power supply 

 
The same instructions as for the DL170 model should be followed (see section 6.1 Connection to the 
power supply, 
p. 37). 
 

8.2.

 

Connection of the antennas: GPRS/3G, Z-Wave (optional) and RF 

 
The terminal of the radio frequency antenna is SMA (Sub Miniature version A). You should verify which 
antenna corresponds to RF and which to GPRS. All dataloggers DL172 have RF and GPRS outputs. 
 

 

The  RF  antenna  should  be  installed  following  the  ESD  protections  to 
prevent damage to the device

 

 
There are two LED lights that show the status of the RF module. If the radio is active, the bottom LED 
will be on. The upper LED will blink whenever the datalogger makes a shipment by RF 
 

8.3.

 

Ethernet port connection 

 
The Ethernet port is in the opposite side to the terminals. 

8.4.

 

GSM/GPRS port connection 

 
The slot for the SIM card is located in the lower right part. A SIM card is needed for the GSM/GPRS 
communications. There is a second slot for the µSD card.  
  
The terminals of the radio frequency and Z-Wave antennas are SMA (Sub Miniature version A). You 
should verify which antenna corresponds to RF and which to GPRS. 
 

 

The GSM/GPRS antenna should be installed following the ESD protections 
to prevent damage to the device 

 

8.5.

 

Digital outputs connection 

 
The  same  instructions  as  for  the  DL170  model  should  be  followed  (see  section  6.6  Digital  outputs 
connection,
 p. 38). 
 

8.6.

 

Connection of the electricity meters 

 
The model DL172 incorporates six internal 3-phase electricity meters. There are three meters in each 
row, each one, with 6 terminals to measure the current (intensity). In addition, in each row there are 4 
terminals for the voltage reference (VN, V1, V2 and V3). The same instructions as for the DL151 model 
should be followed see section 5.5 Connection of the electricity meters, p. 26)
 

Summary of Contents for SENNET DL150
























































































Reviews: