manualshive.com logo in svg

Satec PM171 series, Reference Manual

Share
Download
Satec PM171 series Reference Manual Download Page 40

39

 

5.24  TOU System Registers Setup 

Table 5-55  TOU System Setup Registers 

TOU system register 

Setup registers  

(see Table 5-56) 

TOU energy register  #1 

4564-4565 

TOU energy register  #2 

4566-4567 

TOU energy register  #3 

4568-4569 

TOU energy register  #4 

4570-4571 

TOU energy register  #5 

4572-4573 

TOU energy register  #6 

4574-4575 

TOU energy register  #7 

4576-4577 

TOU energy register  #8 

4578-4579 

TOU Maximum kW demand register 

4580-4581 

N/A 

 4582-4583 

TOU Maximum kVA demand register 

4584-4585 

  Writing to this register is ignored. No error will occur. 

 

Table 5-56  TOU Register Setup 

Parameter 

Offset

Size, 

byte 

Direction

Range 

TOU register input identifier 

+0 

2 

R/W 

see Tables 5-57, 5-58 

For a pulse input = number of 
unit-hours per pulse. Otherwise, 
set to 0. 

+1 2  R/W  0-9999 

1.   Each TOU register consists of 16 tariff registers. 
2.   If a pulse input is assigned to an energy register, the register's input ID must be written first. 

 

Table 5-57  TOU Energy Registers Inputs 

Register input 

 Input ID 

None 

    0 

kWh import 

    1 

kWh export 

    2 

N/A 

 

    3 

N/A 

 

    4 

kvarh import 

    5 

kvarh export 

    6 

N/A 

 

    7 

N/A 

 

    8 

kVAh total   

    9 

Pulse input #1 

   10 

Pulse input #2 

   11 

  Specifying this input will be accepted as NONE. No error will occur. 

 

Table 5-58  TOU Demand Registers Inputs 

Register input 

Input ID 

None 

    0 

N/A 

 

    1 

Maximum sliding window demand 

    2 

N/A 

 

    3 

  Specifying this input will be accepted as NONE. No error will occur. 

Summary of Contents for PM171 series












































Reviews:

No comments

Brands by name

Popular brands

Load more brands