manualshive.com logo in svg

Satec PM171 series, Reference Manual

Share
Download
Satec PM171 series Reference Manual Download Page 34

33

 

Table 5-32  Pulsing Setup Registers 

Parameter 

Offset

Size, 

byte 

Direction 

Range 

Output parameter ID 

+0 

2 

R/W 

see Table 5-33 

Number of unit-hours per pulse 

+1 

2 

R/W 

1-9999 

Table 5-33  Pulsing Output Parameters 

Pulsing parameter 

ID 

None 

    0 

kWh import 

    1 

kWh export 

    2 

kvarh import 

    4 

kvarh export 

    5 

kvarh total (absolute) 

    6 

kVAh total   

    7 

5.16  Relay Operation Control Registers 

These registers allow the user to manually override setpoint relay operations. Either relay may be 
manually operated or released using commands sent via communications. 

NOTES  

1.  A relay allocated as a pulsing relay may not be manually operated or released. When a relay is 

allocated for pulsing, it automatically reverts to normal operation. 

2.  A relay is energized when manually operated, and is de-energized when manually released.  

 

Table 5-34  Relay Operation Control Registers 

Parameter 

Register 

Size, 

byte 

Direction 

Range 

Relay #1 control status 

3244 

2 

R/W 

see Table 5-35 

Relay #2 control status 

3245 

2 

R/W 

see Table 5-35 

 

Table 5-35  Relay Operation Status 

Operation status 

Value 

Normal operation 

0 

Force operate 

1 

Force release 

2 

5.17  Pulse Counters Setup Registers 

Table 5-36  Pulse Counters Registers 

Counter 

Setup registers (see Table 5-37) 

Counter #1 

2940-2941 

Counter #2 

2942-2943 

Counter #3 

2944-2945 

Counter #4 

2946-2947 

 

Table 5-37  Pulse Counter Setup Registers 

Parameter 

Offset

Size, 

byte 

Direction

Range 

Associated digital input ID  

+0 

2 

R/W 

see Table 5-38 

Scale factor (number of units 
per input pulse) 

+1 2  R/W  1-9999 

 

Summary of Contents for PM171 series












































Reviews:

No comments

Brands by name

Popular brands

Load more brands