background image

Opera ons/Procedures/Forks/CAR BODY SAS FORKS Manual v2.pub 2/13/13 2/16/2013 2:50 PM 

 

 

                                    Page 3 

 

www.sasforks.com

                                                                           © 1995

2013 S.A.S. of Luxemburg, Ltd.                                                        1

877

SAS

FORK 

 

S.A.S. of Luxemburg,Ltd. 133 Center Drive Hwy 54, PO Box 260, Luxemburg, WI 54217 USA 

Phone: 920-845-2198 

 

1-877-SAS-FORK  



Fax: 920-845-2309  



Web: www.sasforks.com 

 

TO THE OWNERS, MANAGERS, AND OPERATORS OF LOADERS EQUIPPED 

WITH SAS™ FORKS 

 

Safety is the most important issue in the workplace.  Observing safety guidelines, equipment capacities and using 
common sense will provide a work environment that is safe and efficient for employees, management and  
customers.  It is important that you and your operators read and understand the information included in this  
manual.  A key element to safe operation of this equipment is that all personnel are properly trained. 
Personnel recommended to receive training: Operators and all others working in area where equipment will be  
utilized 
 
Safety warnings are highlighted through out this manual.  Understanding the significance of these symbols is  
important.  The following is a definition of each symbol you will encounter in this manual. 

 

The Caution symbol is intended to draw your attention to important safety information, a  hazard or  
precaution. 

 
The Danger Symbol indicates a hazardous situation that if not avoided  
 will result in serious injury or death 

 
The Warning Symbol indicates a hazardous situation that if not avoided  
could result in serious injury or death 

 
The Caution Symbol indicates a hazardous situation that if not avoided  
could result in minor injury or potential property damage 
 

 
The Notice Symbol indicates worst credible severity of harm is property damage. 

 

The following information laid out in this Operator Manual for SAS FORKS™  is intended to be a guide only, and 
is not meant to encompass all issues that may need to be addressed for your particular type of business operation. 

If you encounter any additional information that would be helpful to us, or others, please contact us. 
 
Thank you for your business, 

 

 

 

 

SAS Ltd.

 

 

     

 

Phone:  

 

 

 

Email: 

S.A.S. OF LUXEMBURG, LTD. 

              

  920-845-2198    

[email protected] 

133 Center Dr Hwy 54 · PO Box 260 

 

LUXEMBURG, WI  54217 USA 

INTRODUCTION LETTER (Page 3) 

SAS™ FORKS 

·Proprietary Rights:

  All designs and other proprietary rights provided by S.A.S. of Luxemburg, Ltd. to Buyer are to 

remain the property of S.A.S. of Luxemburg, Ltd., and Buyer shall honor all proprietary legends.   Notice: The SAS 
FORKS™, this operator manual, 

www.sasforks.com

 web site, the pictures, content, designs, forks, and likeness of such, 

are property of S.A.S. of Luxemburg, Ltd. and are protected under all applicable Copyright, Trade Mark, Trade Dress, 
and Pending Patent.  No information, pictures, designs, or forks may be duplicated in part, entirety, or in likeness.  

Summary of Contents for CAR BODY FORKS




















Reviews: