Sartorius CH3E, Operating Instructions Manual

Page: 53 / 96

53
Classification Application
The “Initialization data” block contains
the upper limits of Classes 1 through 4.
The “Results” block contains gross, net
and tare weights, as well as the class
that the sample belongs to (1 through
5, where Class 5 means that the upper
limit of Class 4 was exceeded).
HEADER LINE 1
HEADER LINE 2
14.07.2002 09:43
--------------------
Lim1
+ 10.000 kg
Lim2 + 11.000 kg
Lim3 + 12.000 kg
Lim4 + 13.000 kg
G# + 9.700 kg
T + 0.000 kg
N + 9.700 kg
Class 1 1
)
--------------------
1
) Classification is based on values
from 1 to 5. Any weight that
exceeds the upper limit defined
for Class 4 is designated as Class 5,
if the application is configured for
5 classes rather than 3.
Animal Weighing Application
The “Initialization data” block contains
the number of measured values that
averaging is based on. The “Results”
block contains the tare weight and the
mean value.
HEADER LINE 1
HEADER LINE 2
14.07.2002 09:43
--------------------
mDef
8
T + 0.000 kg
x-Net + 4.202 kg
--------------------
Net-total Formulation Application
The “Initialization data” block is empty.
Which data is contained in the “Results”
block value depends on the program
operating status at the time of printing.
The following options are available:
– Total/results printout (press
c
)
– Individual/components printout
(When
M+
is pressed to save a
component, or when
p
is pressed
for an individual printout)
‘Total’ printout:
HEADER LINE 1
HEADER LINE 2
14.07.2002 09:43
--------------------
n
3
Tot.cp+ 3.400 kg
Cont.T+ 0.200 kg
--------------------
Individual/Component Printout
If you press
O
the header is printed
only once. Each component is printed
automatically when you press
O
to
store it. If you are using a label printer,
make sure a single label is large enough
for the list of all components. For
printer models YDP01IS and YDP04IS,
you can configure manual form feed in
the operating menu. With the YDP02IS
printer, form feed is automatic after
each print command (fixed setting).
If an automatic printout is generated
when you store a component, the
component weight is equal to the
current net weight. This is why
components rather than net weights are
printed.
Component printout
Example with 3 components
(the corresponding ‘Total’ printout
is shown above):
HEADER LINE 1
HEADER LINE 2
14.07.2002 09:43
--------------------
1.200 kg
2.000 kg
Printout of third component
generated by pressing
p
G# + 4.400 kg
T + 0.200 kg
T2 + 4.200 kg
N + 0.000 kg
Individual printout when a component
is saved in tare memory by pressing
O
Example: Print second component:
HEADER LINE 1
HEADER LINE 2
14.07.2002 09:43
--------------------
1.000 kg
Individual printout of a component
by pressing
p
Example for second component:
HEADER LINE 1
HEADER LINE 2
14.07.2002 09:43
--------------------
G#
+ 2.400 kg
T + 0.200 kg
T2 + 2.200 kg
N + 0.000 kg
Totalizing Application
The “Initialization data” block is empty.
If this block is enabled for the printout,
a blank line is output.
Which data is contained in the “Results”
block value depends on the program
operating status at the time of printing.
The following options are available:
– ‘Results’ printout (press
c
):
Printout of values from gross totalizing
memory “*G”, net totalizing memory
“*N” and number transactions “n”.
– Standard / component printout
automatic (when
M+
is pressed
to save a value)
– Standard / component printout
manual, by pressing
p
.
Whether an individual printout or a
printout of all components is generated
depends on the operating menu
settings.
When the components printout is
configured, the header is printed only
once, followed by all components.
If you are using a label printer, make
sure a single label is large enough for
the list of all components. For printer
models YDP01IS and YDP04IS, you
can configure manual form feed in the
operating menu. If the corresponding
setting is active, you can activate “form
feed” manually. With the YDP02IS
printer, form feed is automatic after
each print command (fixed setting).
When “manual” printing is configured
(press
p
to print) the transaction
counter value is not printed.