Saramonic UwMic10 User Manual Download Page 18 | Manualshive

Page: 18 / 28

background image

/ 16

Operation Guide

1

Install the batteries.

①

UwMic10-RX10 and UwMic10-TX10:

②

UwMic10-HU10

• Long press the Power key to

turn the unit off.

• Slide the two catches inward

and pull out the battery
compartment.

• Insert two AA size batteries

according to the polarity
indicators and close the
compartment. Please be sure
the battery compartment is
locked securely.

• Long press the power button

to turn the power off.

• Turn the grip in the direction

of the arrow, and pull the
grip down until the battery
compartment is visible.

• Insert two new AA

batteries into the battery
compartment with and

polarities in the correct

orientation.

Note:

①

Please remove the batteries from the battery compartment
when the device is not used for a long time.

②

Please always use sets of the same type of battery.

③

Replacing the batteries during operation may generate
noise. Please make sure that the unit is turned off before
replacing batteries.

«
...
16
17
18
19
20
...
»

Summary of Contents for UwMic10





























Reviews:

No comments

Related manuals for UwMic10

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 16

Brand: Cyrus Pages: 6

Brand: Granit Pages: 9

Brand: MPMan Pages: 32

Brand: Samson Pages: 4

Brand: Fifine Pages: 97

Brand: WOXTER Pages: 36

Brand: Trevi Pages: 46

Brand: On-Hold Plus Pages: 12

Brand: Panasonic Pages: 22

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 33

Brand: Panasonic Pages: 15

Brand: Panasonic Pages: 100

Brand: GPX Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands