Saphire Scientific 370 SS Service And Operation Manual Download Page 40

Page: 40 / 81

SECTION 4

SAPPHIRE SCIENTIFIC MODEL 370 SS

PART#

49-038 REV F

9. TROUBLESHOOTING

DO NOT attempt to service this unit while it

is running. High-speed parts as well as high

temperature components may result in severe

injury, severed limbs or fatality.

This section of the operator’s manual describes

how to look for and repair malfunctions, which

may occur.

Accurate troubleshooting is based on a thorough

and complete understanding of the

WATER,

CHEMICAL, VACUUM, HEAT

TRANSFER

SAFETY

and

WIRING

systems

featured in this unit.

If there are malfunctions occurring on this unit

which you do not understand, refer back to the

OPERATION

section of this manual and

review

SYSTEM

TROUBLESHOOTING:

ENGINE

PROBLEM

CAUSE

SOLUTION

Engine will not start:

The

engine does not turn over

Main circuit breaker on the

control panel has been tripped.

After inspecting the unit to determine

the cause of the tripped circuit breaker,

press the reset button.

Loose or corroded battery

connections.

Clean, tighten, or replace the battery

terminals.

Dead battery.

Recharge or replace battery.

Defective ignition switch.

Test ignition switch for power going

into the switch. If there is power going

in but NO power going out, replace the

switch.

Defective starter motor.

Test the starter motor. If necessary

replace.

Vacuum pump seized.

Refer to Gardner Denver Service and

Repair Manual.

Starter turns over engine, but

will not start

Waste tank is full.

Empty the waste tank.

Defective fuel pump.

Replace the fuel pump.

Loose or broken wires leading

to waste tank float switch.

Repair or replace any broken electrical

connections.

Defective float switch in the

waste tank.

Check switch for proper operation,

replace as necessary.

Oil pressure switch (located on

engine), fuel shut-off solenoid

(located on engine).

Test these components. If any are

defective, replace. Consult the Kohler

Engine Operation and Maintenance

Manual.

Engine is malfunctioning

Refer to Kohler Engine Operation and

Maintenance Manual.

Excessive heating

Flow restriction caused by hard

water scaling.

Descale unit, repair or replace

damaged plumbing components as

necessary. Install water softener.

Not enough water flow.

Check jet size of tool and or check the

float valve.

Summary of Contents for 370 SS


















































































Search results

Summary of Contents for 370 SS

Reviews:

Related manuals for 370 SS

Brands by name

Popular brands

Saphire Scientific 370 SS, Service And Operation Manual

Search results

Summary of Contents for 370 SS

Reviews:

Related manuals for 370 SS

Brands by name

Popular brands