Sanyo PLV-HD2000E Service Manual Download Page 14

Page: 14 / 198

AIR FILTER CARE AND CLEANING

Air Filter prevents dust from accumulating on surface of Projection Lens and Projection Mirror. Should Air Filter

become clogged with dust particles, it will reduce Cooling Fans' effectiveness and may result in internal heat build up

and adversely affect life of a projector.

Clean Air Filter following steps below:

Turn power off, and disconnect AC power cord from AC
outlet.

Pull out air filter unit from the projector.

Pulling up center frame of air filter top, separate air filter
top and sheet from air filter base.

Clean each parts with brush, vacuum cleaner dust and

particles.

Assemble sheet, air filter top and air filter base, and
replace air filter unit to a projector.

CAUTION

- Do not operate a projector with air filter removed.

Or dust may accumulate on LCD panel and

Mirror degrading picture quality.

- Do not put small parts into air Intake Vents. Or It

may result in malfunction of a projector.

- The filter be careful and handle. The effect of the

filter runs out in case of a leak and it being

broken off.

AIR FILTER UNIT

AIR FILTER TOP

AIR FILTER BASE

SHEET

Caution; Assembles sheet and filter base

- 14 -

Maintenance and Cleaning

NOTE: If the dust cannot be removed by cleaning, it is

probably time to replace the air filters with new

ones.

Air Filter Parts No. 610 301 4814

Summary of Contents for PLV-HD2000E







































































































































































































Search results

Summary of Contents for PLV-HD2000E

Reviews:

Related manuals for PLV-HD2000E

Brands by name

Popular brands

Sanyo PLV-HD2000E, Service Manual

Search results

Summary of Contents for PLV-HD2000E

Reviews:

Related manuals for PLV-HD2000E

Brands by name

Popular brands