Sanyo PLV-HD2000E Service Manual Download Page 74

Page: 74 / 198

- 74 -

Screw-C (M4 X 6)

(included with Adjustment Tool)

Convergence Adjustment Tool

Screw-B

Guide

Drive screws from this side.

The figure is an installation figure

for the adjustment of the Blue

LCD panel.

Fig. 60d

Step 3

Step 1

Screw-B

Screw-C

Adjustment Tool

Step 2

Loosen 2 Screws-B before remove

Loosen 2 Screws-C
before remove

Prism/LCD Panel
unit

TO REMOVE ADJUSTMENT TOOL

After completing the adjustment, remove the Adjustment Tool as follows.

1. Loosen 2screws-B and release LCD Panel Bracket.

Remove 2screws-C, then remove Adjustment Tool.

2. Slide the Adjustment Tool, and release from the LCD Panel Bracket.

3. Remove the Adjustment Tool upward.

See Fig.60d,60e

Fig. 60e

Slide the

adjustment tool

Optical adjustments

Summary of Contents for PLV-HD2000E







































































































































































































Search results

Summary of Contents for PLV-HD2000E

Reviews:

Related manuals for PLV-HD2000E

Brands by name

Popular brands

Sanyo PLV-HD2000E, Service Manual

Search results

Summary of Contents for PLV-HD2000E

Reviews:

Related manuals for PLV-HD2000E

Brands by name

Popular brands