Sanyo PLC-XTC50AL Specifications Download

Page: 13 / 76

PLC-XTC50AL Expand Serial Command Functional Specifications

13/76

．

Status Read Command Table

6.1 Image Status Read Command Table

Status Read command

Item

CR_BRIGHT [CR]

Get value of Brightness

CR_CONT [CR]

Get value of Contrast

CR_COLOR [CR]

Get value of Color

CR_TINT [CR]

Get value of Tint

CR_SHARP [CR]

Get value of Sharpness

CR_GAMMA [CR]

Get value of Gamma

CR_WBAL-R [CR]

Get Red value of White Balance

CR_WBAL-G [CR]

Get Green value of White Balance

CR_WBAL-B [CR]

Get Blue value of White Balance

CR_COLTEMP [CR]

Get value of Color temperature

CR_NZRED [CR]

Get setting status of Noise reduction

CR_PROGV [CR]

Get setting status of Progressive scan

CR_IMAGE [CR]

Get Selected Image status

CR_IMGGMD [CR]

Get setting value of Image Gamma

6.2 PC Adjust Status Read Command Table

Status Read command

Item

CR_FSYNC [CR]

Get setting value of Fine Sync

CR_TDOTS [CR]

Get setting value of Total Dots

CR_CLPPHASE [CR]

Get setting value of Clamp phase

CR_H-POS [CR]

Get setting value of Horizontal Position

CR_V-POS [CR]

Get setting value of Vertical Position

CR_DDOTS [CR]

Get setting value of Display Dots

CR_DLINE [CR]

Get setting value of Display Line

CR_ORGMODE [CR]

Get the original signal for PC-Adjusted mode

CR_PCSTORE [CR]

Get status Free/ Stored for PC Adj. mode 1-10

CR_SETPCADJ [CR]

Get currently displayed PC signal in system

6.3 Video Status Read Command Table

Status Read command

Item

CR_SERSYS [CR]

Get currently selected signal. In Auto mode, it returns a
result by Auto detection.

Summary of Contents for PLC-XTC50AL













































































Search results

Summary of Contents for PLC-XTC50AL

Reviews:

Related manuals for PLC-XTC50AL

Brands by name

Popular brands

Sanyo PLC-XTC50AL, Specifications

Search results

Summary of Contents for PLC-XTC50AL

Reviews:

Related manuals for PLC-XTC50AL

Brands by name

Popular brands