Sanyo CE14A2-C Service Manual Download Page 47

Page: 47 / 48

Service manual

CHASSIS 2112-Series EC7-A

8. GLOSSARY OF TERMS

ABL

: Auto Beam Limiter. Circuit for limiting the beam current.

AFC

: Automatic frequency control.

AGC

: Auto Gain Control. Voltage that controls the gain of the tuner.

AKB

: Automatic control of beam cathode.

B/G

: TV system. Audio carrier is 5,5MHz. above the video carrier.

BANDGAP

: Voltage reference.

BCI

: Beam Current Information. Voltage which is directly proportional to beam current.

BCL

: See ABL. BCL also refers to the low-pass filtered BCI signal.

CUTOFF

: The point in which the beam current disappears.

CVBS

: Video signal and synchronism.

CHROMA

: Chrominance signal.

D/K

: TV system. Audio carrier is 6,5MHz. above the video carrier.

DRIVER

: Circuit that attacks the base of line transistor.

EEPROM

: Non volatile memory.

EMC

: Electromagnetic compatibility.

: Horizontal frequency.

FLOF

: TXT page navigation by colour links.

FLYBACK

: Signal produced in the line transistor connector during the return of the beam sweeping. It is also called

flyback to the time lapse of the beam return.

HEATER

: CRT cathode heating filaments.

: TV system. Audio carrier is 6MHz above the video carrier.

I2C

: Serial communication bus with two lines, SDA for data and SCL for clock.

: Intermediate frequency.

: Infrared.

: French TV system. Positive video modulation and AM sound.

L’

: Same as L but with inverted signal spectrum.

LIST

: Definition of preferred TXT pages by the user.

MUTE

: Audio mute or video signal blanking.

NVM

: Non volatile memory.

OSD

: On Screen Display. Pictures generated by the microprocessor.

PLL

: Phase locked loop.

PWM

: Pulse width modulation.

SCART

: Euroconnector.

SIF

: Sound intermediate frequency.

SMPS

: Switched mode power supply.

TRC

: Cathode ray tube.

VCO

: Voltage controlled oscillator.

: Luminance signal.

Note:

All information in this manual is correct at the start of production.

SANYO reserves its right to modify components and procedures in order
to comply with its continuous improvement policy.

Summary of Contents for CE14A2-C

















































Search results

Summary of Contents for CE14A2-C

Reviews:

Related manuals for CE14A2-C

Brands by name

Popular brands

Sanyo CE14A2-C, Service Manual

Search results

Summary of Contents for CE14A2-C

Reviews:

Related manuals for CE14A2-C

Brands by name

Popular brands