Sanuvox ASEPT.2X Troubleshooting Manual Download

Page: 31 / 31

defective ballasts)

Electrical wires are disconnected

Plug them properly

One or more relay is disconnected

Connect the relay(s) properly

One relay is defective

Contact SANUVOX (replace the
relay)

The cooling fan doesn’t
work.

Electrical wires are disconnected

Plug them properly

The relay is loosely connected to
the board

Push on the relay to have a tight
connection

Relay’s pins are twisted

Straighten up the pins and firmly
connect the relay.

The relay is defective

Contact SANUVOX (replace the
relay

Only the primary tower
works, not the secondary
tower.

The unit is in « Primary unit only »
mode

In the ADMIN mode on the
tablet, unselect « Primary unit
only »

The lamps don’t shut off
when someone walks in.

One or more motion detectors are
sunk in: the visual filed may be
reduced

Try to fix the motion sensors in a
protruding position

One or more motion detectors are
defective

Contact SANUVOX (replace the
defective sensors)

Cannot access the web
interface.

Disconnected Ethernet cable
between PLC and router

Connect properly the cable

Electrical wires are disconnected

Connect properly the wires

The PLC is defective

Contact SANUVOX (replace or
reprogram the PLC)

Summary of Contents for ASEPT.2X
































Search results

Summary of Contents for ASEPT.2X

Reviews:

Related manuals for ASEPT.2X

Brands by name

Popular brands

Sanuvox ASEPT.2X, Troubleshooting Manual

Search results

Summary of Contents for ASEPT.2X

Reviews:

Related manuals for ASEPT.2X

Brands by name

Popular brands