background image

Step 4A: Attach VMPR1 Top Assembly to Ceiling and install Top Cover - Flat Ceilings

Using the Lag Bolts (

U

) and Lag Bolt Washers (

T

) secure the VMPR1 Top Assembly to the framing member at the location 

selected in 

Step 1: Ceiling Preparation

.

CAUTION:

Do not over tighten the lag Bolts (U). Tighten lag Bolts until they are pulled firmly against the ceiling Plate (C). If 

there is a layer of drywall or other material, this drywall or other material may not exceed 5/8 inch (15.8 mm) in 

thickness. Failure to heed this caution may result in property damage and/or personal injury.

    

Tighten the Lag Bolts (

U

) until the Ceiling Plate (

C

) is flush with the ceiling drywall.

Choose the desired color Top Cover (

H

) and simply slide it over the Adjustment Bracket (

D

) until it fits snugly onto the Ceiling 

Plate (

C

). 

Diagram 4A

U

U

T

T

C

D

H

Step 4B: Attach VMPR1 Top Assembly to Ceiling and install Top Cover - Vaulted or Cathedral Ceilings

Using the Lag Bolts (

U

) and Lag Bolt Washers (

T

) secure the VMPR1 Top Assembly to the framing member at the location 

selected in 

Step 1: Ceiling Preparation

.

CAUTION:

Do not over tighten the lag Bolts (U). Tighten lag Bolts until they are pulled firmly against the ceiling Plate (C). If 

there is a layer of drywall or other material, this drywall or other material may not exceed 5/8 inch (15.8 mm) in 

thickness. Failure to heed this caution may result in property damage and/or personal injury.

     

Tighten the Lag Bolts (

U

) until the Ceiling Plate (

C

) is flush with the ceiling drywall.

Loosen the Pitch Adjustment Screws on the NPT Adapter (

E

) and set the NPT Extension Pipe (

F

) so that it is facing down; 

then, retighten the Pitch Adjustment Screws.

Rotate the Adjustment Bracket (

D

) until the Set Screw (

N

) is facing the screen; then, tighten the Set Screw securing the 

Adjustment Bracket to the NPT Extension Pipe (

F

).

Choose the desired color Top Cover (

H

) and simply slide it over the Adjustment Bracket (

D

) until it fits snugly onto the Ceiling 

Plate (

C

). 

Diagram 4B

U

E

T

D

C

F

H

N

Summary of Contents for VMPR1









Reviews: