background image

2    S&C Instruction Sheet 1041-540

Introduction

Qualified Persons

 WARNING

Only qualified persons who are knowledgeable in the installation, operation, and 
maintenance of overhead and underground electric distribution equipment, along 
with all associated hazards, may install, operate, and maintain the equipment covered 
by this publication . A qualified person is someone who is trained and competent in:
•  The skills and techniques necessary to distinguish exposed live parts from nonlive 

parts of electrical equipment

•  The skills and techniques necessary to determine the proper approach distances 

corresponding to the voltages to which the qualified person will be exposed

•  The proper use of special precautionary techniques, personal protective equipment, 

insulated and shielding materials, and insulated tools for working on or near exposed 
energized parts of electrical equipment

These instructions are intended ONLY for such qualified persons . They are not 
intended to be a substitute for adequate training and experience in safety procedures 
for this type of equipment .

Read this  

Instruction Sheet

NOTICE

Thoroughly and carefully read this instruction sheet and all materials included in 
the product’s instruction handbook before installing or operating a 5800 Series 
Automatic Switch Control . Familiarize yourself with the Safety Information and Safety 
Precautions on pages 3 and 4 . The latest version of this publication is available 
online in PDF format at 

sandc.com/en/support/product-literature/ .

Retain this  

Instruction Sheet

This instruction sheet is a permanent part of your 5800 Series Automatic Switch Control. 
Designate a location where you can easily retrieve and refer to this publication.

Proper Application

 WARNING

The equipment in this publication is only intended for a specific application . The 
application must be within the ratings furnished for the equipment .

Warranty

The warranty and/or obligations described in S&C’s Price Sheet 150, “Standard Conditions 
of Sale–Immediate Purchasers in the United States,” (or Price Sheet 153, “Standard 
Conditions of Sale–Immediate Purchasers Outside the United States,”) plus any special 
warranty provisions, as set forth in the applicable product-line specification bulletin, 
are exclusive. The remedies provided in the former for breach of these warranties shall 
constitute the immediate purchaser’s or end user’s exclusive remedy and a fulfillment of 
the seller’s entire liability. In no event shall the seller’s liability to the immediate purchaser 
or end user exceed the price of the specific product that gives rise to the immediate 
purchaser’s or end user’s claim. All other warranties, whether express or implied or 
arising by operation of law, course of dealing, usage of trade or otherwise, are excluded. 
The only warranties are those stated in Price Sheet 150 (or Price Sheet 153), and THERE 
ARE NO EXPRESS OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS 
FOR A PARTICULAR PURPOSE. ANY EXPRESS WARRANTY OR OTHER OBLIGATION 
PROVIDED IN PRICE SHEET 150 (OR PRICE SHEET 153) IS GRANTED ONLY TO THE 
IMMEDIATE PURCHASER AND END USER, AS DEFINED THEREIN. OTHER THAN AN 
END USER, NO REMOTE PURCHASER MAY RELY ON ANY AFFIRMATION OF FACT OR 
PROMISE THAT RELATES TO THE GOODS DESCRIBED HEREIN, ANY DESCRIPTION 
THAT RELATES TO THE GOODS, OR ANY REMEDIAL PROMISE INCLUDED IN PRICE 
SHEET 150 (or PRICE SHEET 153).

Summary of Contents for 5800 Series









































Reviews: