Network setup
_ 37
The following instructions may vary for your model.
1.
Connect your machine to the network with a network cable.
2.
Insert the Installation CD-ROM, and open the disk window, select
MAC_Installer
>
MAC_Printer
>
SetIP
>
SetIPapplet.html
.
3.
Double click the file and
Safari
will automatically open, then select
Trust
. The browser will open the
SetIPapplet.html
page that shows
the printer’s name and IP address information.
4.
Highlight the printer information row and select the
Setup icon
,
which is the second icon from the left in the application menu bar. A
TCP/IP Configuration window will open.
If the printer was not shown in the information row, select the
Manual Setting icon (third from left) to open the TCP/IP
Configuration window.
5.
Enter the machine’s new information into the configuration window
as follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
•
MAC Address
: Find the machine’s MAC address from the
Network Configuration Report
and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
•
IP Address
: Enter a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150,
enter 192.168.1.X (X is number between 1 and 254 other than
the computer’s address).
•
Subnet Mask
: Enter a Subnet Mask.
•
Default Gateway
: Enter a Default Gateway.
6.
Select
Apply
, then
OK
, and
OK
again. The printer will automatically
print the configuration report. Confirm that all the settings are correct.
Quit Safari
. You may close and eject the installation CD-ROM. If
necessary, restart the computer’s firewall. You have successfully
changed the IP address, subnet mask, and gateway.
IP setting using SetIP Program (Linux)
SetIP program should be automatically installed during the printer driver
installation.
1.
Print the machine’s network configuration report to find your
machine’s MAC address.
2.
Open the /
opt
/
Samsung
/
mfp
/
share
/
utils
/.
3.
Double click the
SetIPApplet.html
file.
4.
Click to open the TCP/IP configuration window.
5.
Enter the network card’s MAC address, IP address, subnet mask,
default gateway, and then click
Apply
.
When you enter the MAC address, enter it without a colon(:).
6.
The machine prints the network information. Confirm all the settings
are correct.
7.
Close the SetIP program.
Network parameter setting
You can also set up the various network settings through the network
administration programs such as
SyncThru™ Web Admin Service
and
SyncThru™ Web Service
.
Restoring factory default settings
You may need to reset the machine to the factory default settings when
machine that you are using is connected to new network environment.
Restoring factory default settings using control panel
1.
Press
Menu
on the control panel.
2.
Press the left/right arrow until
Network
appears and press
OK
.
3.
Press the left/right arrow until
Clear Settings
appears and press
OK
.
4.
Turn off and restart machine to apply settings.
Restoring factory default settings using SyncThru™
Web Service
1.
Start a web browser such as Internet Explorer, Safari or Firefox and
enter your machine’s new IP address in the browser window.
For example,
2.
When the
SyncThru™ Web Service
window opens, click
Network
Settings
.
3.
Click
Reset
. Then, click
Clear
for network.
4.
Turn off and restart machine to apply settings.
INSTALLING WIRED NETWORK OR USB
CONNECTED MACHINE’S DRIVER
Windows
You can set up the machine driver, follow the steps below.
This is recommended for most users. All components necessary for
machine operations will be installed.
1.
Make sure that the machine is connected to the network or USB and
powered on.
2.
Insert the supplied software CD into your CD-ROM drive.
•
The software CD should automatically run and an installation window
appear.
•
If the installation window does not appear, click
Start
and then
Run
.
Type X:\
Setup.exe
, replacing “X” with the letter which represents
your drive. Click
OK
.
•
If you use Windows Vista, Windows 7 and Windows 2008 Server R2
click
Start
>
All programs
>
Accessories
>
Run
.
Type X:\
Setup.exe
replacing “X” with the letter which represents
your drive and click
OK
.
•
If the
AutoPlay
window appears in Windows Vista, click
Run
Setup.exe
in
Install or run program
field, and click
Continue
in the
User Account Control
windows.
•
If the
AutoPlay
window appears in Windows 7 and Windows 2008
Server R2, click
Run
Setup.exe
in
Install or run program
field, and
click
Yes
in the
User Account Control
windows.
Downloaded From ManualsPrinter.com Manuals
