Samsung ProXpress M456x Series Service Manual Download Page 216

Page: 216 / 256

4. Troubleshooting

► Error Code

S6–3128

► Error message

802.1x authentication failed. Please Contact the System Administrator.

► Symptom

Network error. ( A authenticator(eg switch) rejected authentication. / There is no response when checking the ping test.)

► Troubleshooting method

1) Change the machine’s 802.1x credentials.

a) Select “Machine Setup” on the touch screen.

b) Select “Security”

c) Select “802.1x”

d) Select the proper authentication mode for your network environment.

e) Input valid credentials.

2) The System Administrator should check if Ethernet port and authentication server were configured correctly.

► Error Code

S7–2110

► Error message

Fuser Failure: #S7-2110. Turn off then on

► Symptom

Heater control relay is abnormal.

► Troubleshooting method

1) Turn the machine off. Re-install the fuser unit, then turn the machine on.

2) If the problem persists, replace the fuser drive board(FDB).

3) If the problem persists, replace the fuser unit.

4-106

Summary of Contents for ProXpress M456x Series



























































































































































































































































Search results

Summary of Contents for ProXpress M456x Series

Reviews:

Related manuals for ProXpress M456x Series

Brands by name

Popular brands

Samsung ProXpress M456x Series, Service Manual

Search results

Summary of Contents for ProXpress M456x Series

Reviews:

Related manuals for ProXpress M456x Series

Brands by name

Popular brands