Samsung ProXpress M456x Series Service Manual Download

Page: 178 / 256

4. Troubleshooting

► Error Code

C3–1110

► Error message

Prepare new imaging unit.

► Symptom

Imaging unit has almost reached the end of its life.

► Troubleshooting method

1) Prepare the new imaging unit because it will be exhausted soon.

► Error Code

C3–1150

► Error message

Replace with new imaging unit

► Symptom

Imaging unit is at the end of its life.

► Troubleshooting method

1) Open the front cover.

2) Remove the imaging unit and replace it with new one.

3) Close the front cover.

4-68

Summary of Contents for ProXpress M456x Series



























































































































































































































































Search results

Summary of Contents for ProXpress M456x Series

Reviews:

Related manuals for ProXpress M456x Series

Brands by name

Popular brands

Samsung ProXpress M456x Series, Service Manual

Search results

Summary of Contents for ProXpress M456x Series

Reviews:

Related manuals for ProXpress M456x Series

Brands by name

Popular brands