Samsung NX583G0VBSR Service Manual Download

Page: 16 / 67

3. Disassembly and Reassembly

This document can not be used without Samsung’s authorization.

3-5 Removing the Valve Cooktop

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect power before servicing the range . Replace all panels before operating range . Failure to do so

can result in death or electrical shock .

WARNING

EXPLOSION, FIRE, AND ASPHYXIATION HAZARD

Shut off gas supply to the range before servicing . Check all gas lines and fittings for leaks before operating

the range . Replace all panels before operating range . Failure to do so can result in death or personal

injury from explosion, fire, or asphyxiation .

CAUTION

When you work on the gas range, be careful when handling sheet metal parts . Sharp edges may be

present, and you can cut yourself if you are not careful .

Parts

Explanation Photo

Explanation

Switch

Ignition

SWITCH IGNITION

Turn off the electrical supply going

to the range .

Shut off the gas shut-off valve in

the gas supply line to the range .

Remove the ASSY FRAME

COOKTOP, knob and the chassis

manifold panel .

Place a finger behind each side

of the switch ignition and pull it

straight out to release it from the

control shaft . Repeat for each

switch .

Fitting (Gas

line)

FITTING (GAS LINE)

Using a tubing wrench and a

channel-lock wrench, disconnect

the gas lines from the valve

cooktop . Do not bend or crimp gas

lines during removal .

Valve

Cooktop

ASSY VALVE-MANIFOLD

COATING

Remove 2 screws from ASSY

VALVE-MANIFOLD COATING

Note :

When assembling and

disassembling the valve, the

torque should be 1 .5N .m .

Remove the valve cooktop .

Summary of Contents for NX583G0VBSR




































































Search results

Summary of Contents for NX583G0VBSR

Reviews:

Related manuals for NX583G0VBSR

Brands by name

Popular brands

Samsung NX583G0VBSR, Service Manual

Search results

Summary of Contents for NX583G0VBSR

Reviews:

Related manuals for NX583G0VBSR

Brands by name

Popular brands