Samsung NX583G0VBSR Service Manual Download Page 22

Page: 22 / 67

3. Disassembly and Reassembly

This document can not be used without Samsung’s authorization.

3-10 Replacing the Sensor-Thermistor

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect power before servicing the range . Replace all panels before operating range . Failure to do so

can result in death or electrical shock .

WARNING

EXPLOSION, FIRE, AND ASPHYXIATION HAZARD

Shut off gas supply to the range before servicing . Check all gas lines and fittings for leaks before operating

the range . Replace all panels before operating range . Failure to do so can result in death or personal

injury from explosion, fire, or asphyxiation .

CAUTION

When you work on the gas range, be careful when handling sheet metal parts . Sharp edges may be

present, and you can cut yourself if you are not careful .

Parts

Explanation Photo

Explanation

Upper Oven

Burner

Shield and

Upper Oven

Burner

SENSOR THERMISTER

CONNECTOR

Turn off the electrical supply going

to the range .

Shut off the gas shut-off valve in

the gas supply line to the range .

Open the oven door and remove

the racks from inside the oven .

Disconnect connector of the

sensor thermister to the rear of the

range .

The oven sensor thermister is in

the upper left-hand corner of the

oven cavity . Remove 2 screws and

carefully pull the sensor wire leads

until the wire connectors appear .

Reverse the order to install the

oven temperature sensor .

NOTE:

If you can’t access the wire

connectors from inside the

oven, remove the rear cover

panel . Mark and disconnect

the two wires going to the oven

sensor thermister .

Summary of Contents for NX583G0VBSR




































































Search results

Summary of Contents for NX583G0VBSR

Reviews:

Related manuals for NX583G0VBSR

Brands by name

Popular brands

Samsung NX583G0VBSR, Service Manual

Search results

Summary of Contents for NX583G0VBSR

Reviews:

Related manuals for NX583G0VBSR

Brands by name

Popular brands