manualshive.com logo in svg

Samsung NX583G0VBSR, Service Manual

Share
Download
Samsung NX583G0VBSR Service Manual Download Page 14

14

3. Disassembly and Reassembly

This document can not be used without Samsung’s authorization.

3-3 Removing the Assy-Frame Cooktop

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect power before servicing the range . Replace all panels before operating range . Failure to do so 

can result in death or electrical shock .

WARNING

EXPLOSION, FIRE, AND ASPHYXIATION HAZARD

Shut off gas supply to the range before servicing . Check all gas lines and fittings for leaks before operating 

the range . Replace all panels before operating range . Failure to do so can result in death or personal injury 

from explosion, fire, or asphyxiation .

CAUTION

When you work on the gas range, be careful when handling sheet metal parts . Sharp edges may be 

present, and you can cut yourself if you are not careful .

Parts

Explanation Photo

Explanation

Assy-Frame 

Cooktop

ASSY GRATE 

(2 SIDE / 1 CENTER)

BURNER CAP

BURNER HEAD

BURNER CUP

1. 

Turn off the electrical supply 

going to the range .

2. 

Shut off the gas shut-off valve 

in the gas supply line to the 

range .

3. 

Lift off the three grates .

4. 

Lift off the 5 burner caps and 

the 5 burner heads from the 

burner cups .

5. 

Remove screws of the 5 burner 

cups . 

Assy-Frame 

Cooktop

SPRING 

COOKTOP

CHASSIS

MANIFOLD PANEL

FRAME 

COOKTOP

ELECTRODE

6. 

Push the 2 spring located 

between the frame cooktop and 

the chassis manifold panel with 

a thin iron plate . 

Knobs should be removed prior 

to disassembling the cooktop 

frame and take notice that 

Chassis-Manifold Panel is not 

damaged during the operation .

7. 

Push the cups down below the 

surface of the frame cooktop .

NOTE: 

Make sure the electrodes 

are below openings in the 

cooktop to prevent interference 

and damage during removal .

Summary of Contents for NX583G0VBSR




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands