Samsung NX583G0VBSR Service Manual Download

Page: 17 / 67

3. Disassembly and Reassembly

This document can not be used without Samsung’s authorization.

3-6 Replacing the Burner Cup

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect power before servicing the range . Replace all panels before operating range . Failure to do so

can result in death or electrical shock .

WARNING

EXPLOSION, FIRE, AND ASPHYXIATION HAZARD

Shut off gas supply to the range before servicing . Check all gas lines and fittings for leaks before operating

the range . Replace all panels before operating range . Failure to do so can result in death or personal

injury from explosion, fire, or asphyxiation .

CAUTION

When you work on the gas range, be careful when handling sheet metal parts . Sharp edges may be

present, and you can cut yourself if you are not careful .

Parts

Explanation Photo

Explanation

Locking Clip

& Electrode

LOCKING CLIP

ELECTRODE

BURNER CUP

TUBE

Injector

Turn off the electrical supply going

to the range .

Shut off the gas shut-off valve in

the gas supply line to the range .

Remove the frame cooktop .

Using a tubing wrench on the

gas line fitting and a channel lock

wrench on the burner cup base,

firmly hold the cup base in place

while disconnecting the gas line .

To remove the electrode from

the cup, squeeze the two outside

edges of the clip under the

electrode together while pulling to

remove the locking clip . Slide the

electrode and the wire from the

cup . The burner cup can now be

removed .

Summary of Contents for NX583G0VBSR




































































Search results

Summary of Contents for NX583G0VBSR

Reviews:

Related manuals for NX583G0VBSR

Brands by name

Popular brands

Samsung NX583G0VBSR, Service Manual

Search results

Summary of Contents for NX583G0VBSR

Reviews:

Related manuals for NX583G0VBSR

Brands by name

Popular brands