Samsung DS 24D User Instruction Download Page 16

Page: 16 / 131

DS 616

USER INSTRUCTIONS

TECHNICAL MANUAL

PART 1 JUNE 2004

1.15

ACTION

DISPLAY

1. Press

the

Transfer key

followed by

110

Display shows

[201] STN ON/OFF
AME PSWD :OFF

2. Dial the option number from above list (e.g.,

)

[201] STN ON/OFF
HOT KEYPAD :OFF

Press

DOWN

to select the option and

press the right soft key to move the cursor

3. Press

DOWN

to select ON or OFF

Press the left or right soft key to return to step 2

[201] STN ON/OFF
HOT KEYPAD :ON

Dial

for ON or

for OFF

If option 0 from above list is dialed at

Step 2

[201] STN ON/OFF
AUTO HOLD :ON

If option 1 from above list is dialed at

Step 2

[201] STN ON/OFF
AUTO TIMER :ON

If option 2 from above list is dialed at

Step 2

[201] STN ON/OFF
HEADSET USE :OFF

If option 3 from above list is dialed at

Step 2

[201] STN ON/OFF
HOT KEYPAD :ON

If option 4 from above list is dialed at

Step 2

[201] STN ON/OFF
KEYTONE :ON

If option 5 from above list is dialed at

Step 2

[201] STN ON/OFF
PAGE REJOIN :ON

If option 6 from above list is dialed at

Step 2

[201] STN ON/OFF
RING PREF. :ON

If option 7 from above list is dialed at

Step 2

[201] STN ON/OFF
NOT CONT. CID:OFF

If option 8 from above list is dialed at

Step 2

[201] STN ON/OFF
AME PSWD :OFF

4. Press

DOWN

to select ON or OFF

Press the left or right soft key to return to step 2

[201] STN ON/OFF
HOT KEYPAD :ON

5. Press

the

Transfer key

to store and exit

Home Page

Table of Contents

Summary of Contents for DS 24D




































































































































Search results

Summary of Contents for DS 24D

Reviews:

Related manuals for DS 24D

Brands by name

Popular brands

Samsung DS 24D, User Instruction

Search results

Summary of Contents for DS 24D

Reviews:

Related manuals for DS 24D

Brands by name

Popular brands