Samsung DS 24D User Instruction Download Page 114

Page: 114 / 131

AUTO PLAY OF MESSAGE INFORMATION

..................................................

[6][6]

Time & Date Stamp Information. This option can be turned on/off.

AUTO PLAY NEW MESSAGES

...........................................................................

[6][5]

Plays new messages after you log in. This option can be turned on/off.

DIRECT CALL

.........................................................................................................

[#][5]

Used for make out going calls while logged in.

EXTENDED PROMPTING

..............................................................................

[#][7][4]

This option can be turned on/off.

FIND ME

..................................................................................................................

[4][6]

Calls you at a series of numbers in your stored number list.

FOLLOW ME

...........................................................................................................

[4][1]

Changes the number where you are taking your calls.

LISTEN TO NEW MESSAGES

...................................................................................

[1]

LISTEN TO SAVED MESSAGES

...............................................................................

[3]

MESSAGE ALERT

..................................................................................................

[6][1]

When enabled the system will call you to let you know you have new mes-
sages. This option can be turned on/off.

PAGER NOTIFICATION

.......................................................................................

[6][2]

When enabled the system will call your Pager to let you know you have
new messages. This option can be turned on/off.

QUICK MEMO

.....................................................................................

[#][MAILBOX #]

Quickly send a message to another Subscriber.

RECORD AND SEND A MESSAGE

.........................................................................

[2]

REMINDER

................................................................................................................

[#][#]

Quickly send a message to yourself.

STORED TELEPHONE NUMBERS

...................................................................

[#][2]

Enter a list of numbers used by Follow Me, Find Me, and all Notifications.

UNDELETE MESSAGES

........................................................................................[

6][3]

Deleted messages can be recovered any time before Daily Maintenance
time, scheduled by the System Administrator. The default time is 3 a.m.

Quick Reference Index

*Must be Authorized by System Administrator.

Home Page

Table of Contents

Summary of Contents for DS 24D




































































































































Search results

Summary of Contents for DS 24D

Reviews:

Related manuals for DS 24D

Brands by name

Popular brands

Samsung DS 24D, User Instruction

Search results

Summary of Contents for DS 24D

Reviews:

Related manuals for DS 24D

Brands by name

Popular brands