Samsung AM160FNBDEH Installation Manual Download Page 39

Page: 39 / 66

Connecting external contact

Refer to the below table for the terminal numbers that needs on the site for connecting external contact.

Terminal No.

External contact

Operation status / inspection checklist

Remarks

B1, B2

Operation check

Check on/oﬀ status for operation lamp of the control panel on
the site

Optional

B3, B4

Alarm

Check on/oﬀ status for alert lamp of the panel on the site

Optional

B5, B6

Water pump

Check the status of the pump operation signal and on/oﬀ status
of operation at the control panel on the site

Mandatory

B7, B8

Booster heater

Check the status of the heater operation signal output at the
control panel on the site

Optional

B9~B11

3Way valve 1

Check the status of signal output and on/oﬀ status of valve
operation (Direction switch of the indoor hot water tank)

Optional

B12~B14

3Way valve 2

Check the status of signal output and on/oﬀ status of valve
operation (interlocked with solar pump signal)

Optional

B15~B17

2Way valve

Check the status of signal output or operation status of the valve

Optional

B19, B20

AC230, Thermostat 1

Check the connection status of the thermostat and operation
status of the product (cooling)

Optional

B21, B22

AC230, Thermostat 2

Check the connection status of the thermostat and operation
status of the product (heating)

Optional

B23, B24

AC24, Thermostat 1

Check the connection status of the thermostat and operation
status of the product (cooling)

Optional

B25, B26

AC24, Thermostat 2

Check the connection status of the thermostat and operation
status of the product (heating)

Optional

1, 2 (1, 2)

Indoor temperature

sensor

Check the temperature display on the wired remote controller
after separately installing the indoor temperature sensor (Refer to
option setting of the wired remote controller)

Optional

7, 8 (3, 4)

Temperature sensor for

water tank

Check the temperature display on the wired remote controller
after installing the 4~20mA temperature sensor

Mandatory

(hot water supply

operation)

13, 14 (5, 6)

Solar pump

Check the solar pump contact signal input and status of the
operation

Optional

16, 17 (7, 8)

External control

Check the contact signal input and status of the operation

Optional

19, 20 (9, 10)

Smart grid

Check the Smart Grid contact input and the signal

Optional

❋

( ) : Hydro unit HT

k}tGokyvGo{ptXYWZ`]]hTXluUGGGZ_

YWXZTW_TW]GGG㝘㤸G`a[[aZ[

Summary of Contents for AM160FNBDEH



































































Search results

Summary of Contents for AM160FNBDEH

Reviews:

Related manuals for AM160FNBDEH

Brands by name

Popular brands

Samsung AM160FNBDEH, Installation Manual

Search results

Summary of Contents for AM160FNBDEH

Reviews:

Related manuals for AM160FNBDEH

Brands by name

Popular brands