Samsung AM071NN1DEH/TL Instruction Manual Download Page 3

3

English

Saf
ety

 Inf
ormation

 

  WARNING

Hazards or unsafe practices that may result in severe 
personal injury or death.

  CAUTION

Hazards or unsafe practices that may result in minor 
personal injury or property damage.

Carefully follow the precautions listed below because they 
are essential to guarantee the safety of the equipment.

  WARNING

Always disconnect the air conditioner from the power 
supply before servicing it or accessing its internal 
components.

Verify that installation and testing operations are 
performed by qualified personnel.

Verify that the air conditioner is not installed in an 
easily accessible area.

General information

  WARNING

Carefully read the content of this manual before 
installing the air conditioner and store the manual in 
a safe place in order to be able to use it as reference 
after installation.

For maximum safety, installers should always carefully 
read the following warnings.

Store the operation and installation manual in a safe 
location and remember to hand it over to the new 
owner if the air conditioner is sold or transferred. 

This manual explains how to install an indoor unit with 
a split system with two SAMSUNG units. The use of 
other types of units with different control systems may 
damage the units and invalidate the warranty. The 
manufacturer shall not be responsible for damages 
arising from the use of non compliant units.

The manufacturer shall not be responsible for damage 
originating from unauthorized changes or the 
improper connection of electric and requirements set 
forth in the “Operating limits” table, included in the 
manual, shall immediately invalidate the warranty.

The air conditioner should be used only for the applications for 
which it has been designed: the indoor unit is not suitable to 
be installed in areas used for laundry.

Do not use the units if damaged. If problems occur, switch 
the unit off and disconnect it from the power supply.

In order to prevent electric shocks, fires or injuries, 
always stop the unit, disable the protection switch 
and contact SAMSUNG’s technical support if the unit 
produces smoke, if the power cable is hot or damaged 
or if the unit is very noisy.

Always remember to inspect the unit, electric 
connections, refrigerant tubes and protections 
regularly. These operations should be performed by 
qualified personnel only.

The unit contains moving parts, which should always 
be kept out of the reach of children.

Do not attempt to repair, move, alter or reinstall the 
unit. If performed by unauthorized personnel, these 
operations may cause electric shocks or fires.

Do not place containers with liquids or other objects 
on the unit.

All the materials used for the manufacture and 
packaging of the air conditioner are recyclable.

The packing material and exhaust batteries of the 
remote controller(optional) must be disposed of in 
accordance with current laws.

The air conditioner contains a refrigerant that has 
to be disposed of as special waste. At the end of its 
life cycle, the air conditioner must be disposed of in 
authorized centres or returned to the retailer so that it 
can be disposed of correctly and safely.

Installing the unit

  WARNING

IMPORTANT: When installing the unit, always remember 
to connect first the refrigerant tubes, then the electrical 
lines.

Always disassemble the electric lines before the 
refrigerant tubes.

Upon receipt, inspect the product to verify that 
it has not been damaged during transport. If the 
product appears damaged, DO NOT INSTALL it and 
immediately report the damage to the carrier or 
retailer (if the installer or the authorized technician has 
collected the material from the retailer.)

After completing the installation, always carry out a 
functional test and provide the instructions on how to 
operate the air conditioner to the user. 

Safety Information

Summary of Contents for AM071NN1DEH/TL









































Reviews: