background image

EB 8072 EN

 

 9-1

Servicing

9  Servicing

The work described in this section is only to 
be performed by personnel appropriately 

qualified to carry out such tasks.

The following documents are also required 
for servicing the valve:

− 

Mounting and operating instructions for 
the mounted actuator, e.g. 

u

 EB 8310-X 

for Type 3271 or Type 3277 Pneumatic 
Actuator

− 

u

 AB 0100 for tools, tightening torques 

and lubricant

Risk of bursting due to incorrect opening of 

pressurized equipment or components.

Valves and pipelines are pressure equipment 
that may burst when handled incorrectly. 
Flying projectile fragments or the release of 
process medium under pressure can cause 
serious injury or even death.
Before working on the control valve:

 

Î

Depressurize all plant sections affected 
and the valve (including the actuator). 
Release any stored energy.

 

Î

Drain the process medium from all the 
plant sections concerned as well as the 

valve.

Risk of burn injuries due to hot or cold 

components and pipeline.

Valve components and the pipeline may be-
come very hot or cold. Risk of burn injuries.

 

Î

Allow components and pipelines to cool 
down or warm up to the ambient tem-
perature.

 

Î

Wear protective clothing and safety 

gloves.

Risk of personal injury due to pressurized 

components and process medium being 

discharged.

 

Î

Do not loosen the screw of the test con-
nection while the valve is pressurized.

Risk of hearing loss or deafness due to loud 

noise.

Noise emission (e.g. cavitation or flashing) 
may occur during operation caused by the 
process medium and the operating condi-
tions. Additionally, a loud noise may briefly 
occur through the sudden venting of the 
pneumatic actuator or pneumatic valve ac-
cessories not fitted with noise-reducing fit-
tings. Both can damage hearing.

 

Î

Wear hearing protection when working 

near the valve.

Crush hazard arising from actuator and 

plug stem moving.

 

Î

Do not insert hands or finger into the 
yoke while the air supply is connected to 
the actuator.

DANGER

!

WARNING

!

WARNING

!

WARNING

!

WARNING

!

WARNING

!

Summary of Contents for 3291

































































































Reviews: